本文共 51191 字,大约阅读时间需要 170 分钟。
Oracle 11G安装前题
Checking the Hardware Requirements The system must meet the following minimum hardware requirements: • Memory Requirements • System Architecture • Disk Space Requirements 3.1 Memory Requirements The following are the memory requirements for installing Oracle Database 11g Release 2 (11.2): • Minimum: 1 GB of RAM Recommended: 2 GB of RAM or more To determine the RAM size, enter the following command:If the size of the RAM is less than the required size, then you must install more memory before continuing.
• The following table describes the relationship between installed RAM and the configured swap space recommendation: Note: On Linux, the HugePages feature allocates non-swappable memory for large page tables using memory-mapped files. If you enable HugePages, then you should deduct the memory allocated to HugePages from the available RAM before calculating swap space. Available RAM Swap Space Required Between 1 GB and 2 GB 1.5 times the size of the RAM Between 2 GB and 16 GB Equal to the size of the RAM More than 16 GB 16 GB• To determine whether the system architecture can run the software, enter the following command:
• # uname -m Note: This command displays the processor type. Verify that the processor architecture matches the Oracle software release to install. If you do not see the expected output, then you cannot install the software on this system. To determine the size of the configured swap space, enter the following command:If necessary, refer to the operating system documentation for information about how to configure additional swap space.
To determine the available RAM and swap space, enter the following command:Note:
• Oracle recommends that you take multiple values for the available RAM and swap space before finalizing a value. This is because the available RAM and swap space keep changing depending on the user interactions with the computer. • Contact your operating system vendor for swap space allocation guidance for your server. The vendor guidelines supersede the swap space requirements listed in this guide. Automatic Memory Management Starting with Oracle Database 11g, the Automatic Memory Management feature requires more shared memory (/dev/shm)and file descriptors. The shared memory should be sized to be at least the greater of MEMORY_MAX_TARGET and MEMORY_TARGET for each Oracle instance on that computer. To determine the amount of shared memory available, enter the following command:Note:
MEMORY_MAX_TARGET and MEMORY_TARGET cannot be used when LOCK_SGA is enabled or with HugePages on Linux. 3.2 System Architecture To determine whether the system architecture can run the software, enter the following command:Note:
This command displays the processor type. Verify that the processor architecture matches the Oracle software release to install. If you do not see the expected output, then you cannot install the software on this system. 3.3 Disk Space Requirements The following are the disk space requirements for installing Oracle Database 11g Release 2 (11.2): • At least 1 GB of disk space in the /tmp directory To determine the amount of disk space available in the /tmp directory, enter the following command:If there is less than 1 GB of free disk space available in the /tmp directory, then complete one of the following steps:
o Delete unnecessary files from the /tmp directory to meet the disk space requirement. o Set the TMP and TMPDIR environment variables when setting the oracle user’s environment. See Also: “Configuring the oracle User’s Environment” for more information about setting TMP and TMPDIR o Extend the file system that contains the /tmp directory. If necessary, contact the system administrator for information about extending file systems. • To determine the amount of free disk space on the system, enter the following command: • # df -h • The following tables describe the disk space requirements for software files, and data files for each installation type on Linux x86-64: Installation Type Requirement for Software Files (GB) Enterprise Edition 4.7 Standard Edition 4.6 • Installation Type Requirement for Data Files (GB) Enterprise Edition 1.7 Standard Edition 1.5 • • Additional disk space, either on a file system or on an Oracle Automatic Storage Management disk group is required for the fast recovery area if you choose to configure automated backups. 4 Checking the Software Requirements Depending on the products that you intend to install, verify that the following softwares are installed on the system. • Operating System Requirements • Kernel Requirements • Package Requirements • Compiler Requirements • Additional Software Requirements Note: Oracle Universal Installer performs checks on the system to verify that it meets the listed requirements. To ensure that these checks pass, verify the requirements before you start Oracle Universal Installer. Note: The platform-specific hardware and software requirements included in this guide were current when this guide was published. However, because new platforms and operating system software versions might be certified after this guide is published, review the certification matrix on the My Oracle Support website for the most up-to-date list of certified hardware platforms and operating system versions: 4.1 Operating System Requirements The following or later versions of the operating system are required for Oracle Database 11g Release 2 (11.2): Note: • Starting with Oracle Database 11g Release 2 (11.2.0.4), Oracle Linux 7 and Red Hat Enterprise Linux 7 are supported on Linux x86-64. • Starting with Oracle Database 11g Release 2 (11.2.0.3), Oracle Linux 6 and Red Hat Enterprise Linux 6 are supported on Linux x86 and Linux x86-64. • Starting with Oracle Database 11g Release 2 (11.2.0.3), Asianux 4 is supported on Linux x86 and Linux x86-64. • Asianux Server 3 SP2 • Asianux Server 4 SP3 • Oracle Linux 4 Update 7 • Oracle Linux 5 Update 2 (with Red Hat Compatible Kernel) • Oracle Linux 5 Update 5 • Oracle Linux 6 • Oracle Linux 6 (with Red Hat Compatible Kernel) • Oracle Linux 7 • Oracle Linux 7 (with the Red Hat Compatible Kernel) • Red Hat Enterprise Linux 4 Update 7 • Red Hat Enterprise Linux 5 Update 2 • Red Hat Enterprise Linux 6 • Red Hat Enterprise Linux 7 • SUSE Linux Enterprise Server 10 SP2 • SUSE Linux Enterprise Server 11 • SUSE Linux Enterprise Server 12 SP1 • NeoKylin Linux Advanced Server 6 Starting with Oracle Database 11g Release 2 (11.2), the Security Enhanced Linux (SE Linux) feature is supported for Oracle Linux 4, Oracle Linux 5, Oracle Linux 6, Red Hat Enterprise Linux 4, Red Hat Enterprise Linux 5, and Red Hat Enterprise Linux 6. To determine the distribution and version of Linux installed, enter the following command:4.2 Kernel Requirements
The following are the kernel requirements for Oracle Database 11g Release 2 (11.2): • On Oracle Linux 4 and Red Hat Enterprise Linux 4 2.6.9 or later • On Oracle Linux 5 Update 2 with Red Hat Compatible Kernel 2.6.18 or later • On Oracle Linux 5 Update 5 with Red Hat Compatible Kernel 2.6.18 or later • On Oracle Linux 5 Update 5 with Unbreakable Enterprise Kernel 2.6.32-100.0.19 or later • On Oracle Linux 6 2.6.32-100.28.5.el6.x86_64 or later • On Oracle Linux 6 with Red Hat Compatible Kernel 2.6.32-71.el6.x86_64 or later • On Oracle Linux 7 3.8.13-33.el7uek.x86_64 or later • On Oracle Linux 7 with Red Hat Compatible Kernel 3.10.0-54.0.1.el7.x86_64 or later • On Red Hat Enterprise Linux 5 Update 2 2.6.18 or later • On Red Hat Enterprise Linux 5 Update 5 2.6.18 or later • On Red Hat Enterprise Linux 6 2.6.32-71.el6.x86_64 or later • On Red Hat Enterprise Linux 7 3.10.0-54.0.1.el7.x86_64 or later • On Asianux Server 3 2.6.18 or later • On Asianux Server 4 2.6.32-71.el6.x86_64 or later • On SUSE Linux Enterprise Server 10 2.6.16.21 or later • On SUSE Linux Enterprise Server 11 2.6.27.19 or later • On SUSE Linux Enterprise Server 12 3.12.49-11 or later • On NeoKylin Linux Advanced Server 6 2.6.32-431.el6.x86_64 or later See Also: “About Oracle Unbreakable Enterprise Kernel for Linux” section in Oracle Database Installation Guide for Linux To determine whether the required kernel is installed, enter the following command:The following is a sample output displayed by running this command on an Oracle Linux 5.0 system:
2.6.18-128.el5PAE In this example, the output shows the kernel version (2.6.18) and errata level (-128.el5PAE) on the system. If the kernel version does not meet the requirement specified earlier in this section, then contact the operating system vendor for information about obtaining and installing kernel updates. 4.3 Package Requirements The following are the list of packages required for Oracle Database 11g Release 2 (11.2): Note: • Oracle recommends that you install your Linux operating system with the default software packages (RPMs), unless you specifically intend to perform a minimal installation, and follow the directions for performing such an installation to ensure that you have all required packages for Oracle software. • Oracle recommends that you do not customize RPMs during a default operating system installation. A default installation includes most required packages, and helps you to limit manual checks of package dependencies. • If you did not perform a default Linux installation, you intend to use LDAP, and you want to use the scripts odisrvreg, oidca, or schemasync, then install the Korn shell RPM for your Linux distribution. • You must install the packages (or later versions) listed in the following table. Also, ensure that the list of RPMs and all the prerequisites for these RPMs are installed. • If you are using Oracle Unbreakable Enterprise Kernel, then all required kernel packages are installed as part of the Oracle Unbreakable Enterprise Kernel installation. • For Orace Linux 6 the Oracle Validated RPM has been replaced by the Oracle RDBMS Server 11gR2 Pre-install RPM. See the “Completing a Minimal Linux Installation” section in Oracle Database Installation Guide. Note: Starting with Oracle Database 11g Release 2 (11.2.0.2), all the 32-bit packages, except for gcc-32bit-4.3, listed in the following table are no longer required for installing a database on Linux x86-64. Only the 64-bit packages are required. However, for any Oracle Database 11g release before 11.2.0.2, both the 32-bit and 64-bit packages listed in the following table are required. • The following or later version of packages for Oracle Linux 4 and Red Hat Enterprise Linux 4 must be installed: • binutils-2.15.92.0.2 • compat-libstdc+±33-3.2.3 • compat-libstdc+±33-3.2.3 (32 bit) • elfutils-libelf-0.97 • elfutils-libelf-devel-0.97 • expat-1.95.7 • gcc-3.4.6 • gcc-c+±3.4.6 • glibc-2.3.4-2.41 • glibc-2.3.4-2.41 (32 bit) • glibc-common-2.3.4 • glibc-devel-2.3.4 • glibc-headers-2.3.4 • libaio-0.3.105 • libaio-0.3.105 (32 bit) • libaio-devel-0.3.105 • libaio-devel-0.3.105 (32 bit) • libgcc-3.4.6 • libgcc-3.4.6 (32-bit) • libstdc+±3.4.6 • libstdc+±3.4.6 (32 bit) • libstdc+±devel 3.4.6 • make-3.80 • numactl-0.6.4.x86_64 • pdksh-5.2.14 • sysstat-5.0.5 • The following or later version of packages for Oracle Linux 5, Red Hat Enterprise Linux 5, and Asianux Server 3 must be installed: • binutils-2.17.50.0.6 • compat-libstdc+±33-3.2.3 • compat-libstdc+±33-3.2.3 (32 bit) • elfutils-libelf-0.125 • elfutils-libelf-devel-0.125 • gcc-4.1.2 • gcc-c+±4.1.2 • glibc-2.5-24 • glibc-2.5-24 (32 bit) • glibc-common-2.5 • glibc-devel-2.5 • glibc-devel-2.5 (32 bit) • glibc-headers-2.5 • ksh-20060214 • libaio-0.3.106 • libaio-0.3.106 (32 bit) • libaio-devel-0.3.106 • libaio-devel-0.3.106 (32 bit) • libgcc-4.1.2 • libgcc-4.1.2 (32 bit) • libstdc+±4.1.2 • libstdc+±4.1.2 (32 bit) • libstdc+±devel-4.1.2 • make-3.81 • sysstat-7.0.2 • The following or later version of packages for Oracle Linux 6, Red Hat Enterprise Linux 6, and Asianux Server 4 must be installed: • binutils-2.20.51.0.2-5.11.el6 (x86_64) • compat-libcap1-1.10-1 (x86_64) • compat-libstdc+±33-3.2.3-69.el6 (x86_64) • compat-libstdc+±33-3.2.3-69.el6.i686 • gcc-4.4.4-13.el6 (x86_64) • gcc-c+±4.4.4-13.el6 (x86_64) • glibc-2.12-1.7.el6 (i686) • glibc-2.12-1.7.el6 (x86_64) • glibc-devel-2.12-1.7.el6 (x86_64) • glibc-devel-2.12-1.7.el6.i686 • ksh • libgcc-4.4.4-13.el6 (i686) • libgcc-4.4.4-13.el6 (x86_64) • libstdc+±4.4.4-13.el6 (x86_64) • libstdc+±4.4.4-13.el6.i686 • libstdc+±devel-4.4.4-13.el6 (x86_64) • libstdc+±devel-4.4.4-13.el6.i686 • libaio-0.3.107-10.el6 (x86_64) • libaio-0.3.107-10.el6.i686 • libaio-devel-0.3.107-10.el6 (x86_64) • libaio-devel-0.3.107-10.el6.i686 • make-3.81-19.el6 • sysstat-9.0.4-11.el6 (x86_64) • The following or later version of packages for Oracle Linux 7, and Red Hat Enterprise Linux 7 must be installed: • binutils-2.23.52.0.1-12.el7.x86_64 • compat-libcap1-1.10-3.el7.x86_64 • compat-libstdc+±33-3.2.3-71.el7.i686 • compat-libstdc+±33-3.2.3-71.el7.x86_64 • gcc-4.8.2-3.el7.x86_64 • gcc-c+±4.8.2-3.el7.x86_64 • glibc-2.17-36.el7.i686 • glibc-2.17-36.el7.x86_64 • glibc-devel-2.17-36.el7.i686 • glibc-devel-2.17-36.el7.x86_64 • ksh • libaio-0.3.109-9.el7.i686 • libaio-0.3.109-9.el7.x86_64 • libaio-devel-0.3.109-9.el7.i686 • libaio-devel-0.3.109-9.el7.x86_64 • libgcc-4.8.2-3.el7.i686 • libgcc-4.8.2-3.el7.x86_64 • libstdc+±4.8.2-3.el7.i686 • libstdc+±4.8.2-3.el7.x86_64 • libstdc+±devel-4.8.2-3.el7.i686 • libstdc+±devel-4.8.2-3.el7.x86_64 • libXi-1.7.2-1.el7.i686 • libXi-1.7.2-1.el7.x86_64 • libXtst-1.2.2-1.el7.i686 • libXtst-1.2.2-1.el7.x86_64 • make-3.82-19.el7.x86_64 • sysstat-10.1.5-1.el7.x86_64 • The following or later version of packages for SUSE Linux Enterprise Server 10 must be installed: • binutils-2.16.91.0.5 • compat-libstdc+±5.0.7 • gcc-4.1.0 • gcc-c+±4.1.2 • glibc-2.4-31.63 • glibc-devel-2.4-31.63 • glibc-devel-32bit-2.4-31.63 • ksh-93r-12.9 • libaio-0.3.104 • libaio-32bit-0.3.104 • libaio-devel-0.3.104 • libaio-devel-32bit-0.3.104 • libelf-0.8.5 • libgcc-4.1.2 • libstdc+±4.1.2 • libstdc+±devel-4.1.2 • make-3.80 • numactl-0.9.6.x86_64 • sysstat-8.0.4 • The following or later version of packages for SUSE Linux Enterprise Server 11 must be installed: • binutils-2.19 • gcc-4.3 • gcc-32bit-4.3 • gcc-c+±4.3 • glibc-2.9 • glibc-32bit-2.9 • glibc-devel-2.9 • glibc-devel-32bit-2.9 • ksh-93t • libaio-0.3.104 • libaio-32bit-0.3.104 • libaio-devel-0.3.104 • libaio-devel-32bit-0.3.104 • libstdc++33-3.3.3 • libstdc++33-32bit-3.3.3 • libstdc++43-4.3.3_20081022 • libstdc++43-32bit-4.3.3_20081022 • libstdc++43-devel-4.3.3_20081022 • libstdc++43-devel-32bit-4.3.3_20081022 • libgcc43-4.3.3_20081022 • libstdc+±devel-4.3 • make-3.81 • sysstat-8.1.5 • The following or later version of packages for SUSE Linux Enterprise Server 12: must be installed: • binutils-2.25.0-13.1 • gcc-4.8-6.189 • gcc48-4.8.5-24.1 • glibc-2.19-31.9 • glibc-32bit-2.19-31.9 • glibc-devel-2.19-31.9.x86_64 • glibc-devel-32bit-2.19-31.9.x86_64 • libaio1-0.3.109-17.15 • libaio-devel-0.3.109-17.15 • libcap1-1.10-59.61 • libstdc++48-devel-4.8.5-24.1.x86_64 • libstdc++48-devel-32bit-4.8.5-24.1.x86_64 • libstdc++6-5.2.1+r226025-4.1.x86_64 • libstdc++6-32bit-5.2.1+r226025-4.1.x86_64 • libstdc+±devel-4.8-6.189.x86_64 • libstdc+±devel-32bit-4.8-6.189.x86_64 • libgcc_s1-5.2.1+r226025-4.1.x86_64 • libgcc_s1-32bit-5.2.1+r226025-4.1.x86_64 • mksh-50-2.13 • make-4.0-4.1.x86_64 • sysstat-10.2.1-3.1.x86_64 • xorg-x11-driver-video-7.6_1-14.30.x86_64 • xorg-x11-server-7.6_1.15.2-36.21.x86_64 • xorg-x11-essentials-7.6_1-14.17.noarch • xorg-x11-Xvnc-1.4.3-7.2.x86_64 • xorg-x11-fonts-core-7.6-29.45.noarch • xorg-x11-7.6_1-14.17.noarch • xorg-x11-server-extra-7.6_1.15.2-36.21.x86_64 • xorg-x11-libs-7.6-45.14.noarch • xorg-x11-fonts-7.6-29.45.noarch Note: You must download and install patch 18370031. For more information about how to download and install this patch, see: Oracle Database Client Installation Guide for Linux • The following or later version of packages for NeoKylin Linux Advanced Server 6 must be installed: • binutils-2.20.51.0.2-5.36.el6 (x86_64) • compat-libcap1-1.10-1 (x86_64) • compat-libstdc+±33-3.2.3-69.el6 (x86_64) • compat-libstdc+±33-3.2.3-69.el6 (i686) • gcc-4.4.7-4.el6 (x86_64) • gcc-c+±4.4.7-4.el6 (x86_64) • glibc-2.12-1.132.el6 (i686) • glibc-2.12-1.132.el6 (x86_64) • glibc-devel-2.12-1.132.el6 (x86_64) • glibc-devel-2.12-1.132.el6 (i686) • ksh • libgcc-4.4.7-4.el6 (i686) • libgcc-4.4.7-4.el6 (x86_64) • libstdc+±4.4.7-4.el6 (x86_64) • libstdc+±4.4.7-4.el6 (i686) • libstdc+±devel-4.4.7-4.el6 (x86_64) • libstdc+±devel-4.4.7-4.el6 (i686) • libaio-0.3.107-10.el6 (x86_64) • libaio-0.3.107-10.el6 (i686) • libaio-devel-0.3.107-10.el6 (x86_64) • libaio-devel-0.3.107-10.el6 (i686) • make-3.81-20.el6 • sysstat-9.0.4-22.el6 (x86_64) To determine whether the required packages are installed, enter commands similar to the following:If a package is not installed, then install it from the Linux distribution media or download the required package version from the Linux vendor’s website.
4.4 Compiler Requirements Intel C++ Compiler 10.1 or later and the version of GNU C and C++ compilers listed under “Package Requirements” are supported with these products. Note: Intel Compiler v10.1 can be used only with the standard template libraries of the gcc versions mentioned in the Package Requirements section, to build Oracle C++ Call Interface (OCCI) applications. Oracle XML Developer’s Kit is supported with the same compilers as OCCI. 4.5 Additional Software Requirements Depending on the components you want to use, you must ensure that the following software are installed: • Oracle ODBC Drivers • Oracle JDBC/OCI Drivers • Linux-PAM Library • Oracle Messaging Gateway • Programming Languages • Browser Requirements 4.5.1 Oracle ODBC Drivers You should install ODBC Driver Manager for UNIX. You can download and install the Driver Manager from the following URL: To use ODBC, you must also install the following additional ODBC RPMs, depending on your operating sytem: • On Oracle Linux 4 and Red Hat Enterprise Linux 4: o unixODBC-2.2.11 (32-bit) or later o unixODBC-devel-2.2.11 (64-bit) or later o unixODBC-2.2.11 (64-bit) or later • On Oracle Linux 5, Red Hat Enterprise Linux 5, and Asianux Server 3: o unixODBC-2.2.11 (32-bit) or later o unixODBC-devel-2.2.11 (64-bit) or later o unixODBC-2.2.11 (64-bit) or later • On Oracle Linux 6, Red Hat Enterprise Linux 6, and Asianux Server 4: o unixODBC-2.2.14-11.el6 (x86_64) or later o unixODBC-2.2.14-11.el6.i686 or later o unixODBC-devel-2.2.14-11.el6 (x86_64) or later o unixODBC-devel-2.2.14-11.el6.i686 or later • On Oracle Linux 7, and Red Hat Enterprise Linux 7: o unixODBC-2.3.1-6.el7.x86_64 or later o unixODBC-2.3.1-6.el7.i686 or later o unixODBC-devel-2.3.1-6.el7.x86_64 or later o unixODBC-devel-2.3.1-6.el7.i686 or later • On SUSE 10: o unixODBC-32 bit-2.2.11 (32-bit) or later o unixODBC-2.2.11 (64-bit) or later o unixODBC-devel-2.2.11 (64-bit) or later • On SUSE 11: o unixODBC-2.2.12 or later o unixODBC-devel-2.2.12 or later o unixODBC-32bit-2.2.12 (32-bit) or later 4.5.2 Oracle JDBC/OCI Drivers Use JDK 6 (Java SE Development Kit 1.6.0_21) or JDK 5 (1.5.0_24) with the JNDI extension with the Oracle Java Database Connectivity and Oracle Call Interface drivers. However, these are not mandatory for the database installation. Note that IBM JDK 1.5 is installed with this release. 4.5.3 Linux-PAM Library Install the latest Linux-PAM (Pluggable Authentication Modules for Linux) library to enable the system administrator to choose how applications authenticate users. 4.5.4 Oracle Messaging Gateway Oracle Messaging Gateway supports the integration of Oracle Streams Advanced Queuing (AQ) with the following software: • IBM WebSphere MQ V7.0, client and server: • MQSeriesClient • MQSeriesServer • MQSeriesRuntime • TIBCO Rendezvous 7.3 If you require a CSD for WebSphere MQ, then refer to the IBM website for download and installation information: 4.5.5 Programming Languages The following products are certified for use with: • Pro* COBOL Micro Focus Server Express 5.1 4.5.6 Browser Requirements You do not require a web browser to install Oracle Database. However, browsers are required to access documentation, and if you intend to use Oracle Enterprise Manager Database Control and Oracle Application Express. Web browsers must support JavaScript, and the HTML 4.0 and CSS 1.0 standards. Oracle Enterprise Manager Database Control supports the following browsers: • Microsoft Internet Explorer 10.0 (supports Oracle Enterprise Manager Database Control 11.2.0.3 and higher) • Microsoft Internet Explorer 9.0 • Microsoft Internet Explorer 8.0 • Microsoft Internet Explorer 7.0 SP1 • Microsoft Internet Explorer 6.0 SP2 • Firefox 21.0 (supports Oracle Enterprise Manager Database Control 11.2.0.4) • Firefox 17.0.6 ESR (supports Oracle Enterprise Manager Database Control 11.2.0.4) • Firefox 3.6 • Firefox 3.5 • Firefox 3.0.7 • Firefox 2.0 • Safari 4.0.x • Safari 3.2 • Safari 3.1 • Google Chrome 27.0 (supports Oracle Enterprise Manager Database Control 11.2.0.4) • Google Chrome 4.0 • Google Chrome 3.0 • Netscape Navigator 9.0 • Netscape Navigator 8.1 See Also: Oracle Application Express Installation Guide 5 Creating Required Operating System Groups and Users The following local operating system groups and users are required if you are installing Oracle Database: • The Oracle Inventory group (typically, oinstall) • The OSDBA group (typically, dba) • The Oracle software owner (typically, oracle) • The OSOPER group (optional. Typically, oper) To determine whether these groups and users exist, and if necessary, to create them, follow these steps:If the output of this command shows the oinstall group name, then the group exists.
If the oraInst.loc file exists, then the output from this command is similar to the following: inventory_loc=/u01/app/oraInventory inst_group=oinstall The inst_group parameter shows the name of the Oracle Inventory group, oinstall. 3. To determine whether the dba group exists, enter the following command: 4. # grep dba /etc/group If the output from this commands shows the dba group name, then the group exists. 5. If necessary, enter the following commands to create the oinstall and dba groups: 6. # /usr/sbin/groupadd oinstall 7. # /usr/sbin/groupadd dba 8. To determine whether the oracle user exists and belongs to the correct groups, enter the following command: 9. # id oracle If the oracle user exists, then this command displays information about the groups to which the user belongs. The output should be similar to the following, indicating that oinstall is the primary group and dba is a secondary group: uid=440(oracle) gid=200(oinstall) groups=201(dba),202(oper) 10. If necessary, complete one of the following actions: o If the oracle user exists, but its primary group is not oinstall or it is not a member of the dba group, then enter the following command: o # /usr/sbin/usermod -g oinstall -G dba oracle o If the oracle user does not exist, enter the following command to create it: o # /usr/sbin/useradd -g oinstall -G dba oracle This command creates the oracle user and specifies oinstall as the primary group and dba as the secondary group. 11. Enter the following command to set the password of the oracle user: 12. # passwd oracle 6 Configuring Kernel Parameters and Resource Limits Verify that the kernel parameters shown in the following table are set to values greater than or equal to the minimum value shown. The procedure following the table describes how to verify and set the values. Note: The kernel parameter and shell limit values in this section are minimum values only. For production database systems, Oracle recommends that you tune these values to optimize the performance of the system. Refer to your operating system documentation for more information about tuning kernel parameters. Parameter Minimum Value File semmsl semmns semopm semmni 250 32000 100 128 /proc/sys/kernel/sem shmall 2097152 /proc/sys/kernel/shmall shmmax Minimum: 536870912 Maximum: A value that is 1 byte less than the physical memory Recommended: More than half the physical memory See My Oracle Support Note 567506.1 for additional information about configuring shmmax. /proc/sys/kernel/shmmax shmmni 4096 /proc/sys/kernel/shmmni file-max 6815744 /proc/sys/fs/file-max ip_local_port_range Minimum: 9000 Maximum: 65500 /proc/sys/net/ipv4/ip_local_port_range rmem_default 262144 /proc/sys/net/core/rmem_default rmem_max 4194304 /proc/sys/net/core/rmem_max wmem_default 262144 /proc/sys/net/core/wmem_default wmem_max 1048576 /proc/sys/net/core/wmem_max aio-max-nr 1048576 Note: This value limits concurrent outstanding requests and should be set to avoid I/O subsystem failures. /proc/sys/fs/aio-max-nrNote:
If the current value of any parameter is higher than the value listed in this table, then do not change the value of that parameter. To view the current value specified for these kernel parameters, and to change them if necessary: • Enter commands similar to the following to view the current values of the kernel parameters: Note: Make a note of the current values and identify any values that you must change. Parameter Command semmsl, semmns, semopm, and semmni # /sbin/sysctl -a | grep sem This command displays the value of the semaphore parameters in the order listed. shmall, shmmax, and shmmni # /sbin/sysctl -a | grep shm file-max # /sbin/sysctl -a | grep file-max ip_local_port_range # /sbin/sysctl -a | grep ip_local_port_range rmem_default # /sbin/sysctl -a | grep rmem_default rmem_max # /sbin/sysctl -a | grep rmem_max wmem_default # /sbin/sysctl -a | grep wmem_default wmem_max # /sbin/sysctl -a | grep wmem_max• If the value of any kernel parameter is different from the recommended value, then complete the following steps:
Review the output from this command to verify that the values are correct. If the values are incorrect, edit the /etc/sysctl.conf file, then enter this command again.
4. Enter the command /sbin/sysctl -a to confirm that the values are set correctly. 5. On SUSE systems only, enter the following command to cause the system to read the /etc/sysctl.conf file when it restarts: 6. # /sbin/chkconfig boot.sysctl on 7. On SUSE systems only, you must enter the GID of the oinstall group as the value for the parameter /proc/sys/vm/hugetlb_shm_group. Doing this grants members of oinstall a group permission to create shared memory segments. For example, where the oinstall group GID is 501:After running this command, use vi to add the following text to /etc/sysctl.conf, and enable the boot.sysctl script to run on system restart:
vm.hugetlb_shm_group=501 Note: Only one group can be defined as the vm.hugetlb_shm_group. 8. After updating the values of kernel parameters in the /etc/sysctl.conf file, either restart the computer, or run the command sysctl -p to make the changes in the /etc/sysctl.conf file available in the active kernel memory. Check Resource Limits for the Oracle Software Installation Users For each installation software owner, check the resource limits for installation, using the following recommended ranges: Table 1 Installation Owner Resource Limit Recommended Ranges Resource Shell Limit Resource Soft Limit Hard Limit Open file descriptors nofile at least 1024 at least 65536 Number of processes available to a single user nproc at least 2047 at least 16384 Size of the stack segment of the process stack at least 10240 KB at least 10240 KB, and at most 32768 KBTo check resource limits:
This command displays information about all the file systems mounted on the system, including:
o The physical device name o The total amount, used amount, and available amount of disk space o The mount point directory for that file system 3. From the display, identify either one or two file systems that meet the disk space requirements mentioned earlier in this section. 4. Note the name of the mount point directory for each file system that you identified. 5. Enter commands similar to the following to create the recommended subdirectories in the mount point directory that you identified and set the appropriate owner, group, and permissions on them: 6. # mkdir -p /mount_point/app/ 7. # chown -R oracle:oinstall /mount_point/app/ 8. # chmod -R 775 /mount_point/app/ For example:8 Configuring the oracle User’s Environment
You run Oracle Universal Installer from the oracle account. However, before you start Oracle Universal Installer, you must configure the environment of the oracle user. To configure the environment, you must: • Set the default file mode creation mask (umask) to 022 in the shell startup file. • Set the DISPLAY environment variable. To set the oracle user’s environment:11 Installing Oracle Database Examples
If you plan to use the following products or features, then download and install the products from the Oracle Database Examples media: • Oracle JDBC Development Drivers • Oracle Database Examples • Various Oracle product demonstrations For information about installing software and various Oracle product demonstrations from the Oracle Database Examples media, refer to Oracle Database Examples Installation Guide. 12 What to Do Next? To become familiar with this release of Oracle Database, it is recommended that you complete the following tasks: • Log in to Oracle Enterprise Manager Database Control using a web browser. Oracle Enterprise Manager Database Control is a web-based application that you can use to manage a single Oracle Database installation. The default URL for Database Control is similar to the following: To log in, use the user name SYS and connect as SYSDBA. Use the password that you specified for this user during the Oracle Database 11g installation. • Refer to Oracle Database Installation Guide for Linux for information about required and optional postinstallation tasks, depending on the products to use. • Refer to Oracle Database Installation Guide for Linux for information about how to use Database Control to learn about the configuration of your installed database. • To learn more about using Oracle Enterprise Manager Database Control to administer a database, refer to Oracle Database 2 Day DBA. This guide, designed for new Oracle DBAs, describes how to use Database Control to manage all aspects of an Oracle Database installation. It also provides information about how to enable e-mail notifications and automated backups, which you might not have configured during the installation. 13 Additional Information This section contains information about the following: • Product Licenses • Purchasing Licenses and Version Updates • Contacting Oracle Support Services • Locating Product Documentation Product Licenses You are welcome to install and evaluate the products included in this media pack for 30 days under the terms of the Trial License Agreement. However, you must purchase a program license if you want to continue using any product after the 30 day evaluation period. See the following section for information about purchasing program licenses. Purchasing Licenses and Version Updates You can purchase program licenses and updated versions of Oracle products from the Oracle Store website: Contacting Oracle Support Services If you have purchased Oracle Product Support, you can call Oracle Support Services for assistance 24 hours a day, seven days a week. For information about purchasing Oracle Product Support or contacting Oracle Support Services, go to the Oracle Support Services website: Locating Product Documentation Product documentation includes information about configuring, using, or administering Oracle products on any platform. The product documentation for Oracle Database products is available in both HTML and PDF formats online: 14 Documentation Accessibility For information about Oracle’s commitment to accessibility, visit the Oracle Accessibility Program website at . Access to Oracle Support Oracle customers that have purchased support have access to electronic support through My Oracle Support. For information, visit or visit if you are hearing impaired.Oracle Database Quick Installation Guide, 11g Release 2 (11.2) for Linux x86-64
E24326-08 Copyright © 2016, Oracle and/or its affiliates. All rights reserved. This software and related documentation are provided under a license agreement containing restrictions on use and disclosure and are protected by intellectual property laws. Except as expressly permitted in your license agreement or allowed by law, you may not use, copy, reproduce, translate, broadcast, modify, license, transmit, distribute, exhibit, perform, publish, or display any part, in any form, or by any means. Reverse engineering, disassembly, or decompilation of this software, unless required by law for interoperability, is prohibited. The information contained herein is subject to change without notice and is not warranted to be error-free. If you find any errors, please report them to us in writing. If this is software or related documentation that is delivered to the U.S. Government or anyone licensing it on behalf of the U.S. Government, then the following notice is applicable: U.S. GOVERNMENT END USERS: Oracle programs, including any operating system, integrated software, any programs installed on the hardware, and/or documentation, delivered to U.S. Government end users are “commercial computer software” pursuant to the applicable Federal Acquisition Regulation and agency-specific supplemental regulations. As such, use, duplication, disclosure, modification, and adaptation of the programs, including any operating system, integrated software, any programs installed on the hardware, and/or documentation, shall be subject to license terms and license restrictions applicable to the programs. No other rights are granted to the U.S. Government. This software or hardware is developed for general use in a variety of information management applications. It is not developed or intended for use in any inherently dangerous applications, including applications that may create a risk of personal injury. If you use this software or hardware in dangerous applications, then you shall be responsible to take all appropriate fail-safe, backup, redundancy, and other measures to ensure its safe use. Oracle Corporation and its affiliates disclaim any liability for any damages caused by use of this software or hardware in dangerous applications. Oracle and Java are registered trademarks of Oracle and/or its affiliates. Other names may be trademarks of their respective owners. Intel and Intel Xeon are trademarks or registered trademarks of Intel Corporation. All SPARC trademarks are used under license and are trademarks or registered trademarks of SPARC International, Inc. AMD, Opteron, the AMD logo, and the AMD Opteron logo are trademarks or registered trademarks of Advanced Micro Devices. UNIX is a registered trademark of The Open Group. This software or hardware and documentation may provide access to or information about content, products, and services from third parties. Oracle Corporation and its affiliates are not responsible for and expressly disclaim all warranties of any kind with respect to third-party content, products, and services unless otherwise set forth in an applicable agreement between you and Oracle. Oracle Corporation and its affiliates will not be responsible for any loss, costs, or damages incurred due to your access to or use of third-party content, products, or services, except as set forth in an applicable agreement between you and Oracle.转载地址:http://gvodi.baihongyu.com/